Voltage Divider Calculator
Work out a voltage divider's output with Vout = Vin × R2 ÷ (R1 + R2), solve for R1 or R2, see how a load pulls it down and find the closest E-series pair.
Still loading. If the tool doesn’t appear, reload this page.
About this tool
Voltage Divider Calculator
Find a divider's output voltage, solve for R1 or R2, see the effect of a load, and get the closest standard E-series resistor pair.
A voltage divider calculator finds the output of two resistors in series: Vout = Vin × R2 ÷ (R1 + R2), so 12 V across 10 kΩ and 4.7 kΩ gives 3.84 V. It also solves for R1 or R2, accounts for a load, and finds the closest standard E-series pair.
How to use Voltage Divider Calculator
- 1
Choose what to solve for — output voltage, R1 or R2 — and enter the input voltage plus the other values (type resistances like 4.7k or 10k).
- 2
Optionally enter the load resistance connected across the output; the result then shows the loaded voltage, the unloaded voltage and how far the load pulls it down.
- 3
Under Standard resistor pair, pick an E-series and a rough total resistance to get the closest standard R1 and R2, with the output error in percent.
Why use Voltage Divider Calculator
Solves any unknown
Output voltage, R1 or R2 from the other values.
Load-aware
Puts the load in parallel with R2 and shows the drop, divider current, resistor power and output resistance.
Standard pairs
Searches real E6–E96 values near your chosen total and ranks pairs by output error.
Standard E24 divider pairs for common voltages
| Conversion | R1 (top) | R2 (bottom) | Output | Error |
|---|---|---|---|---|
| 5 V → 3.3 V | 4.7 kΩ | 9.1 kΩ | 3.297 V | −0.088 % |
| 5 V → 2.5 V | 5.1 kΩ | 5.1 kΩ | 2.5 V | 0 % |
| 12 V → 5 V | 18 kΩ | 13 kΩ | 5.032 V | +0.65 % |
| 12 V → 3.3 V | 2.4 kΩ | 910 Ω | 3.299 V | −0.027 % |
| 24 V → 5 V | 9.1 kΩ | 2.4 kΩ | 5.009 V | +0.17 % |
| 3.3 V → 1.8 V | 3 kΩ | 3.6 kΩ | 1.8 V | 0 % |
Errors are from the nominal values only; resistor tolerance adds to them. A divider is not a power supply — use a regulator to power a load.
Common use cases
- Scale a 12 V battery voltage down below 3.3 V for a microcontroller's analogue input.
- Level-shift a 5 V signal to 3.3 V with two standard resistors.
- Check how much a 10 kΩ load drags down a high-value divider.
- Work out R2 for a target output when R1 is already on the board.
Frequently asked questions
What is the voltage divider formula?
Vout = Vin × R2 ÷ (R1 + R2), where R1 is the top resistor and R2 the one to ground. With 12 V, R1 = 10 kΩ and R2 = 4.7 kΩ, Vout = 12 × 4.7 ÷ 14.7 ≈ 3.84 V.
How do I get 3.3 V from 5 V with resistors?
Use R1 ≈ 0.515 × R2. With standard E24 values, 4.7 kΩ over 9.1 kΩ gives 3.297 V, within 0.1 %. That suits a logic or ADC input, not powering a 3.3 V device.
How do I calculate R2 for a voltage divider?
R2 = R1 × Vout ÷ (Vin − Vout). For 5 V to 3.3 V with R1 = 10 kΩ, R2 = 10,000 × 3.3 ÷ 1.7 ≈ 19.4 kΩ. Solving for R1 instead: R1 = R2 × (Vin − Vout) ÷ Vout.
Why does a voltage divider's output drop under load?
The load sits in parallel with R2 and lowers the bottom resistance. A 4.7 kΩ load on a 10 kΩ / 4.7 kΩ divider from 12 V pulls the output from 3.84 V to 2.28 V. Keep the load resistance much larger than R2, or use a buffer.
Can I power a circuit from a voltage divider?
Usually not. The output voltage changes as the load current changes, and the divider wastes current all the time. Dividers are for reference and signal levels; use a voltage regulator to power a load.
What total resistance should a voltage divider have?
It is a trade-off: low values waste more current, high values are pulled down more by the load. Enter your load resistance and the calculator shows how far the output drops.
Embed this tool on your site
Add the Voltage Divider Calculator widget to your blog or website — free, responsive, no signup. Just keep the “Widget by AltFTool” credit link visible.
<iframe src="https://www.altftool.com/embed/widget/voltage-divider-calculator"
title="Voltage Divider Calculator — free AltFTool widget"
width="100%" height="640" style="border:0;border-radius:12px;overflow:hidden"
loading="lazy" referrerpolicy="no-referrer-when-downgrade" allow="clipboard-write"></iframe>
<p style="font-size:12px;margin:4px 0 0">Widget by <a href="https://www.altftool.com/tools/all/voltage-divider-calculator?utm_source=embed&utm_medium=widget" rel="nofollow">AltFTool — free online tools</a></p>