LTL and truckload freight
Know your freight density before you ask for rates
Measure each pallet, turn the numbers into pounds per cubic foot, and prepare the shipment the way LTL carriers expect. Then compare LTL, partial and full truckload in plain words before you request a single quote.
- A density calculator for one or more pallets
- A shipment prep checklist you can print
- LTL, partial and full truckload side by side
Density calculator
Work out freight density in pounds per cubic foot
Enter the size of one handling unit, such as a loaded pallet, how many identical units you are shipping and their total weight. If your units differ in size, run each size separately.
Measure at the longest point, counting the pallet and any overhang.
Measure from the floor to the top of the load, pallet and all.
Weigh on a scale with pallets and wrap. Carriers can reweigh freight and bill the difference.
Your shipment
Arithmetic from the measurements you enter: cubic feet are length times width times height in inches, divided by 1,728. It is not a quote, a price or a freight class; confirm the class for your commodity with your carrier.
Shipping modes
LTL, partial and full truckload compared
The right mode depends on how much space and weight you need and how much handling your freight can take.
| Typical difference | LTL | Partial truckload | Full truckload |
|---|---|---|---|
| Typical load | Often one to six pallets | Too big for LTL, short of a full trailer | A whole trailer, by space or weight |
| Price based on | Weight, freight class, distance and extras | Space used, weight and distance | Mostly the lane and the equipment |
| Freight class needed | Usually yes | Often not | No |
| Handling | Moves through terminals, may change trucks | Fewer stops, often one truck | Loaded once, stays on the trailer |
| Transit time | Longer, with terminal stops | Often shorter than LTL | Usually the most direct |
| Good fit when | Small loads and flexible timing | Mid-size loads or fragile freight | Heavy or high-volume loads |
Scroll the table sideways to see every column.
Carriers and brokers define these modes in their own ways. Compare quotes on the same pickup, drop-off, pieces, weight and services.
Shipment prep
Prepare each pallet before pickup
Tick items as you go, then print the list for the dock or reset it for the next load. Your ticks stay on this page only.
0 of 17 done
Carriers publish their own packaging and labeling rules in their tariffs. Where a rule here and your carrier's rule differ, follow the carrier.
Freight terms
The words on a freight quote
Quotes and bills of lading use the same handful of terms. Knowing them makes two quotes easier to compare.
- LTL (less than truckload)
- Freight that shares a trailer with other shippers' freight. You pay for your part of the trailer, based mainly on weight, freight class, distance and any extra services.
- FTL (full truckload)
- One shipper books the whole trailer. The price is mostly set per trip on a lane, whether the trailer fills up by space or by weight.
- Bill of lading (BOL)
- The document that lists the shipper, consignee, pieces, weight, description and class. It is the receipt for the freight and sets out the terms of carriage.
- Freight class
- A rating from 50 to 500 that LTL carriers use in pricing, based on density, handling, stowability and liability. Lower classes usually cost less per pound.
- NMFC
- The National Motor Freight Classification, the standard that assigns commodities to freight classes. It is published by the National Motor Freight Traffic Association (NMFTA).
- Accessorial charges
- Fees for services beyond a standard dock-to-dock move, such as a liftgate, residential or limited-access drop-off, inside delivery, appointments or a reweigh.
- Liftgate
- A powered platform at the back of a truck that lowers freight from trailer height to the ground where there is no dock. It usually costs extra and is booked in advance.
- PRO number
- The tracking number a carrier assigns to an LTL shipment, often printed on a sticker attached to the bill of lading.
Booking a shipment
From measurements to a signed bill of lading
Most LTL shipments follow the same path, whether you book with a carrier directly or through a broker.
Gather the details
Pickup and drop-off addresses, dock or no dock, the commodity, pieces, weight and dimensions, and the date the freight is ready.
Check density and class
Run the numbers through the density calculator, then confirm the commodity's NMFC item and class with the carrier or broker.
Compare like with like
Ask several carriers or brokers to price the same details, and compare transit times, extra charges and liability limits as well as the rate.
Book and fill in the BOL
Book a pickup window, then complete the bill of lading with the same weight, class and description you were quoted on.
Hand over and track
Have the freight wrapped and labeled at the dock before the window opens, collect the driver's signature on the BOL and keep the PRO number.
Check it at drop-off
The receiver counts pieces and looks for damage before signing. Any shortage or damage should be written on the delivery receipt.
Questions to ask
Ask every carrier or broker the same questions
The same questions on every quote make the answers easier to line up afterwards.
- Which accessorial charges could apply to this shipment, and what does each one cost?
- How do you handle a reweigh or a class change, and can I see the inspection record?
- What is your liability limit for this freight, and how do I declare a higher value?
- Is the transit time an estimate or a committed service level?
- What pickup window can you offer, and how much notice do you need?
- Does the receiver need a delivery appointment or a call before drop-off?
- How do I report damage, and what is the deadline for a claim?
FAQ
Common questions about LTL freight
What is freight density, and why does it matter?
Freight density is the weight of a shipment in pounds divided by its volume in cubic feet. LTL carriers use density, together with handling, stowability and liability, to set the freight class for many commodities. Denser freight usually falls into a lower class, which often means a lower rate per pound.
How do I find the right freight class?
Freight class starts with your commodity's NMFC listing: some items are classed by density, others have a set class. Work out the density, then confirm the class with your carrier or broker before booking. The NMFTA publishes the classification, and a wrong class can lead to a reclass and extra charges after pickup.
When does a full truckload make more sense than LTL?
A full truckload starts to make sense when freight fills most of a trailer by space or weight, or when it is fragile and should be handled as little as possible. The crossover depends on the lane and the freight, so many shippers compare LTL, partial and full truckload quotes once a load grows past several pallets.
What happens if the weight or dimensions on my bill of lading are wrong?
LTL carriers can inspect, reweigh and remeasure freight at their terminals. If the numbers differ from the bill of lading, the carrier may change the class and bill the difference, sometimes with an inspection fee, under its tariff. Weighing and measuring every pallet before pickup avoids most of these corrections.
Does a carrier pay the full value of damaged freight?
Not always. Carrier liability for freight is often limited, for example by weight or by terms in the carrier's tariff, unless you declare a higher value or arrange separate cargo coverage. Ask about limits before shipping, note any damage on the delivery receipt, and file a claim within the deadline in the carrier's terms.
Can CargoLoom book a freight shipment for me?
No. CargoLoom Freight Quotes is a design demonstration by AltFTool, so its quote and booking buttons are placeholders that send nothing, and no carrier sees your details. Use the density calculator and prep checklist here, then ask carriers or brokers you choose for quotes.
AltFTool email
New calculators from AltFTool
CargoLoom is a demo brand and keeps no mailing list. If the density calculator helped, you can sign up for AltFTool's own email list; the consent box below spells out what that involves.
Measured and wrapped?
Run the density calculator again with your final numbers, tick the prep checklist and keep both handy when you compare quotes.
About these demos
Shipping and logistics page designs with fictional brands
AltFTool's Shipping & Logistics demos are landing-page designs for moving goods, all with fictional brands: CargoLoom for freight quotes, SwiftSatchel for local courier runs, ShelfRunner for e-commerce fulfillment, BorderLedger for customs brokerage, BoxBeacon for parcel shipping and PalletPier for pallet storage.
Calculators on these pages work out freight density, dimensional weight, storage and fulfillment costs from the measurements and rates you enter. None of these brands moves, stores or clears goods, quote buttons are disabled, and customs and carrier rules should be confirmed with the carrier or authority concerned.
Frequently asked questions
Are CargoLoom, BoxBeacon and the other AltFTool logistics brands real carriers?
CargoLoom, BoxBeacon, SwiftSatchel, ShelfRunner, BorderLedger and PalletPier are fictional brands made for AltFTool's logistics page designs. None of them carries freight, handles parcels, stores pallets or files customs entries, and AltFTool offers none of these services, so quote requests on these pages reach nobody.
How is dimensional weight worked out on AltFTool's BoxBeacon demo?
The BoxBeacon demo on AltFTool multiplies a box's length, width and height in inches, divides by the divisor you choose and compares the result with the actual weight, because carriers usually bill the higher of the two. Divisors differ between carriers and services, so check your carrier's current rules.
Can AltFTool's customs demo tell me how much duty my goods will owe?
No part of AltFTool's BorderLedger customs demo can classify goods or work out duty. Duty depends on the tariff classification, origin and value of the goods and on the rules in force, so confirm it with U.S. Customs and Border Protection or a customs broker before you ship.
What happens to measurements typed into AltFTool's shipping calculators?
Measurements and rates typed into AltFTool's shipping calculators are worked out in your browser and are not stored or sent. Only an email address entered in a sign-up box is saved, by AltFTool, which sends one email to confirm it, and every message has an unsubscribe link.
People also search for
- freight broker website design
- courier service landing page
- 3pl fulfillment website
- customs broker website
- parcel shipping website design
- warehouse storage landing page