Find the leaks first
Find where your home loses heat before you upgrade
Hunt for drafts room by room with a printable checklist, see what a professional energy audit usually covers, and use a short quiz to pick where to start: air sealing, insulation, windows or heating and cooling.
- A room-by-room draft checklist you can print
- A quiz that suggests where to start
- What a professional audit usually involves
DIY draft hunt
Hunt for drafts room by room
Pick a cold, windy day, or run the kitchen and bath exhaust fans to pull outside air through leaks. Ticks are not saved, so print the list if you want to keep your notes.
0 of 18 done
A DIY hunt finds obvious leaks but does not measure them. A professional blower door test shows how leaky the whole house is.
Where to start
Which upgrade should you read about first?
Answer four questions about how your home feels. The result points to an area to read about; an energy auditor can confirm the priorities for your house.
Professional audits
What a professional energy audit usually covers
Audits vary by program and auditor, but most follow a pattern like this. Ask any auditor what their visit involves.
Conversation and bills
The auditor asks about comfort problems and may look over a year of energy bills to see how the house uses energy.
Walk-through
A room-by-room look at insulation, windows, doors, the attic, the basement or crawlspace, and heating and cooling equipment.
Blower door test
A powerful fan set in an exterior door lowers the air pressure inside, so the auditor can measure how leaky the house is and find the leaks.
Thermal imaging
Many auditors use an infrared camera during the blower door test to spot missing insulation and air leaks as temperature patterns.
Safety checks
Fuel-burning appliances are checked for proper venting and carbon monoxide, which matters more as a house gets tighter.
Report and priorities
A written report lists recommended upgrades, often in order of priority, so you can plan the work.
Results vary
What affects how much an upgrade can save
Two similar-looking houses can get very different results from the same upgrade. These are the main reasons.
Climate
Homes in very cold or very hot places run heating or cooling longer, so cutting heat loss or gain has more to work on.
Starting point
A leaky, lightly insulated house usually has more to gain than one that was built or upgraded tight.
Fuel type and price
What you pay for electricity, gas, oil or propane sets the dollar value of every unit of energy you save.
Equipment efficiency
An efficient heating and cooling system uses less energy to begin with, which leaves less to save.
How you use the home
Thermostat settings, how many people live there and the hours the home is occupied all shape energy use.
Quality of the work
Gaps, compressed insulation or missed spots can undercut an upgrade, so how well it is installed matters.
Results differ from home to home, and no single figure fits every house. Treat any savings estimate as a rough guide, and ask an auditor how they arrived at it.
Audit terms
Energy audit terms in plain words
The words you are likely to see in an audit report.
- Blower door test
- A diagnostic that uses a calibrated fan in an exterior door to lower the air pressure inside and measure how much air leaks in.
- CFM50 and ACH50
- Two ways to report blower door results: airflow in cubic feet per minute at 50 pascals of pressure, and how many times an hour the home's air would be replaced at that pressure. Lower numbers mean a tighter house.
- R-value
- A measure of how well a material resists heat flow. A higher R-value insulates better; the right level depends on climate and where the insulation goes.
- Air sealing
- Closing gaps and cracks with caulk, foam, weatherstripping or gaskets so heated or cooled air stays in and outside air stays out.
- Thermal imaging
- Using an infrared camera to see differences in surface temperature that can reveal missing insulation and air leaks.
- Stack effect
- Warm air rises and escapes through leaks high in the house, pulling cold air in through leaks low down. It is why attic and basement leaks matter.
- Combustion safety check
- A check that fuel-burning appliances vent properly and are not producing excess carbon monoxide.
Questions to ask
Questions for an energy auditor
These help you compare auditors and understand what you are paying for.
- Does the audit include a blower door test and thermal imaging?
- Do you check fuel-burning appliances for safe venting and carbon monoxide?
- What does the written report cover, and are upgrades ranked by priority?
- Do you also sell or install upgrades, or only do audits?
- Are there utility or state programs that help pay for the audit or upgrades here?
- Can the house be measured again after the work to see what changed?
- What training or credentials do you hold for this work?
FAQ
Common questions about home energy audits
What is a home energy audit?
A home energy audit is an assessment of where a house loses energy and what to fix first. A professional audit usually adds a blower door test, often thermal imaging and safety checks of fuel-burning appliances, and ends with a written list of recommended upgrades.
How long does a professional energy audit take?
Often a few hours, depending on the size of the home, how easy the attic and crawlspaces are to reach, and which checks are done. Ask the auditor how long to plan for and whether you need to be home for the whole visit.
Should I air seal or add insulation first?
Air sealing usually comes first, especially in the attic, because insulation laid over open gaps does not stop air moving through them and makes the gaps harder to reach later. An energy auditor can confirm the right order for your house.
Is a DIY energy audit worth doing?
A DIY draft hunt costs nothing and can turn up obvious leaks around doors, windows, outlets and the attic hatch. It cannot measure how leaky the whole house is or check combustion safety, which is where a professional energy audit adds something.
How much can an energy audit save me?
An audit on its own saves nothing; the upgrades you make afterwards are what can lower energy use. How much depends on your climate, your home's starting point, fuel prices and the quality of the work, so results vary widely. Treat any single figure as a rough guide.
Can DraftSeal book an energy audit for me?
No. DraftSeal Home Energy Audits is a demo created by AltFTool, and its booking buttons are placeholders that send nothing. To arrange an audit, ask your utility whether it runs an audit program, or contact an auditor you choose.
AltFTool email
More tools from AltFTool
DraftSeal is not a real company and has no email list. AltFTool, which built this demo, keeps one for news of new tools, and the box below states what you agree to.
Start with the leaks you can find yourself
Work through the draft checklist, try the where-to-start quiz, and bring your notes to an energy auditor.
About these demos
Home energy and utility page designs with fictional brands
AltFTool's Energy & Utilities demos are landing-page designs for home energy services, all with fictional brands: RateRidge for electricity plans, AmpNest for EV charging, SteadyCurrent for backup power, DraftSeal for energy audits, AquaLedger for water treatment and HearthFuel for propane and heating oil.
The calculators on these pages work from the numbers you enter, such as kilowatt-hours, miles driven or tank size, and none of them quotes a real rate. No brand sells energy or installs equipment, and electrical, gas and water decisions belong with your utility, a qualified installer and local codes.
Frequently asked questions
Are RateRidge, AmpNest and the other AltFTool energy brands real companies?
RateRidge, AmpNest, SteadyCurrent, DraftSeal, AquaLedger and HearthFuel are fictional brands made for AltFTool's energy page designs. None of them supplies electricity or fuel, installs chargers or generators, or tests water, and AltFTool sells none of these, so quote requests on these pages reach no company.
How does the EV charging cost calculator on AltFTool's AmpNest demo work?
The AmpNest calculator on AltFTool divides the miles you drive by your car's miles per kilowatt-hour, allows for charging losses and multiplies by the electricity rate you enter. The result is arithmetic from your own numbers, so check the rate you actually pay on your utility bill.
Who should install a home EV charger or a standby generator?
A home EV charger or standby generator is usually installed by a qualified electrician, often under a local permit, and a generator should feed home wiring only through a transfer switch. AltFTool's energy demos describe these steps in general terms and cannot assess any particular home.
What happens to the numbers typed into AltFTool's energy calculators?
Numbers typed into AltFTool's energy calculators are worked out in your browser and are not stored or sent anywhere. Only an email address entered in a sign-up box is saved, by AltFTool, which sends one email to confirm it, and you can unsubscribe from any message.
People also search for
- electricity plan comparison website
- ev charger installer website
- generator installer landing page
- home energy audit website
- water treatment company website
- propane delivery website design