Skip to main content

Skip to content

Home water treatment, step by step

Choose water treatment based on what is in your water

Learn what sediment filters, carbon filters, reverse osmosis and softeners each do, use a short quiz to see which to read about, and size a softener from your own hardness and household numbers.

  • Four common system types in plain words
  • A softener sizing worksheet in grains per day
  • A reminder to test your water first

System types

What common home water systems do

Each system handles a different kind of problem, and none treats everything. Many homes combine two, such as a sediment filter ahead of a softener.

Sediment filter

Catches sand, silt, rust flakes and other particles. It is often fitted first in line to protect fixtures and other equipment, and its cartridges need regular changes.

  • Particles
  • Often first in line

Carbon filter

Activated carbon reduces chlorine taste and odor, and some other chemicals depending on the filter. Sizes range from pitchers and faucet units to whole-house tanks.

  • Taste and odor
  • Many sizes

Reverse osmosis

Pushes water through a fine membrane that reduces dissolved solids and many other dissolved substances. Usually fitted under one sink, with a storage tank and a drain line.

  • Dissolved solids
  • One tap

Water softener

Swaps the calcium and magnesium that cause hardness for sodium or potassium, then cleans itself with salt during regeneration. It softens water; it does not purify it.

  • Hardness
  • Uses salt

Treatment quiz

Which treatment should you read about?

Answer based on what you notice at the tap. The result names a system type to read about, and the first step is always the same: test your water.

1. What do you notice most?
2. Where does your water come from?
3. Where do you want treated water?
4. What has a water test shown so far?

Test your water before you choose a system

If you are on a public water system, read your utility's annual water quality report, often called a Consumer Confidence Report. If you have a private well, testing is up to you; your state or local health department can suggest labs and what to test for.

Softener sizing

Work out how many grains a softener must remove

A softener's capacity is measured in grains of hardness. Multiply your household's water use by its hardness to see the load the softener has to handle.

4 people

An example value. If you have a water bill, divide the household's daily use by the number of people.

From a water test. If the result is in mg/L or ppm, divide it by 17.1 to get grains per gallon.

Use the capacity at the salt setting you plan to use; the headline figure is often the maximum.

Your hardness load

Grains to remove per day3,000 grains
Grains to remove per week21,000 grains
Days between regenerations8.0 days

Arithmetic from the numbers you enter, not a quote or a dealer's sizing. Iron, manganese and the softener's own design also affect sizing, so ask the seller or manufacturer to check the figure.

Water terms

Water treatment terms in plain words

Words you will see on water tests and product data sheets.

Hardness
The amount of dissolved calcium and magnesium in water. Hard water leaves scale in pipes, kettles and water heaters.
Grains per gallon (gpg)
The usual unit for hardness in softener sizing. One grain per gallon equals about 17.1 milligrams per liter.
Parts per million (ppm)
A concentration unit used on many water tests. For water it is about the same as milligrams per liter (mg/L).
TDS
Total dissolved solids: everything dissolved in the water, from minerals to salts, as one number. A TDS reading does not say which substances are present.
Regeneration
The cycle in which a softener flushes its resin with salt water to restore its capacity, using water and salt each time.
Micron rating
The particle size a filter is designed to catch. A smaller number means finer filtration and usually more frequent cartridge changes.
Point of use and point of entry
Point-of-use systems treat water at one tap; point-of-entry systems treat all the water coming into the house.

Questions to ask

Questions for any water treatment seller

Ask every seller the same questions, and ask to see the answers in writing.

  • Which result from my water test is this system meant to address?
  • Can I see the performance data sheet for this exact model?
  • How did you size it for my household's water use and hardness?
  • How much salt, water and electricity does it use?
  • What maintenance does it need, and what do replacement filters or membranes cost?
  • Does it need a drain or an outlet nearby, and is a plumbing permit required here?
  • What does the manufacturer cover, and for how long?

FAQ

Common questions about home water treatment

How do I know if I have hard water?

Common signs are white scale on faucets and kettles, spots on dishes and soap that does not lather well. A water test confirms it: your utility's water quality report may list hardness, home test strips give a rough reading, and a lab test is more precise.

What size water softener do I need?

Multiply the people in your home by daily water use per person and by hardness in grains per gallon. That gives grains per day; a softener's usable capacity divided by that figure gives the days between regenerations. Iron and other minerals change the math, so ask the seller to check it.

Does a water softener make water safe to drink?

No. A water softener removes hardness minerals; it is not designed to purify water or remove most contaminants. If you are concerned about what is in your water, have it tested and talk to your local health department or utility before choosing any treatment.

Does reverse osmosis waste water?

A reverse osmosis system sends part of the water it processes down the drain, carrying away what the membrane holds back. How much varies by system and water pressure, so check the product's data sheet for the ratio of drained water to treated water.

How often should well water be tested?

Many health agencies suggest testing a private well at least once a year, and again after flooding or any change in taste, color or smell. Your state or local health department can tell you which tests make sense where you live.

Can AquaLedger test my water or install a system?

No. AquaLedger Water Systems is a fictional brand in an AltFTool design demo, so its consult and quote buttons are placeholders that send nothing. For testing, start with your utility's water quality report or your local health department.

Test first, then choose with your numbers

Read your water quality report or test your well, take the quiz, and size any softener from your own hardness figures.

About these demos

Home energy and utility page designs with fictional brands

AltFTool's Energy & Utilities demos are landing-page designs for home energy services, all with fictional brands: RateRidge for electricity plans, AmpNest for EV charging, SteadyCurrent for backup power, DraftSeal for energy audits, AquaLedger for water treatment and HearthFuel for propane and heating oil.

The calculators on these pages work from the numbers you enter, such as kilowatt-hours, miles driven or tank size, and none of them quotes a real rate. No brand sells energy or installs equipment, and electrical, gas and water decisions belong with your utility, a qualified installer and local codes.

Frequently asked questions

Are RateRidge, AmpNest and the other AltFTool energy brands real companies?

RateRidge, AmpNest, SteadyCurrent, DraftSeal, AquaLedger and HearthFuel are fictional brands made for AltFTool's energy page designs. None of them supplies electricity or fuel, installs chargers or generators, or tests water, and AltFTool sells none of these, so quote requests on these pages reach no company.

How does the EV charging cost calculator on AltFTool's AmpNest demo work?

The AmpNest calculator on AltFTool divides the miles you drive by your car's miles per kilowatt-hour, allows for charging losses and multiplies by the electricity rate you enter. The result is arithmetic from your own numbers, so check the rate you actually pay on your utility bill.

Who should install a home EV charger or a standby generator?

A home EV charger or standby generator is usually installed by a qualified electrician, often under a local permit, and a generator should feed home wiring only through a transfer switch. AltFTool's energy demos describe these steps in general terms and cannot assess any particular home.

What happens to the numbers typed into AltFTool's energy calculators?

Numbers typed into AltFTool's energy calculators are worked out in your browser and are not stored or sent anywhere. Only an email address entered in a sign-up box is saved, by AltFTool, which sends one email to confirm it, and you can unsubscribe from any message.

People also search for

  • electricity plan comparison website
  • ev charger installer website
  • generator installer landing page
  • home energy audit website
  • water treatment company website
  • propane delivery website design